{"product_id":"isuzu-and-gwm-p-series-wheel-spacer-with-spigot","title":"Isuzu and GWM P Series Wheel Spacer with Spigot","description":"\u003cp\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cfont size=\"3\"\u003eWheel spacer with spigot ring for B Series and D-Max\u003c\/font\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003e\u003cstrong\u003eNOTE:\u003c\/strong\u003e The Spigot does not go over the Hub on the front wheels. On a 4×4 Isuzu you will only be able to use these spacers on the rear wheels and you will have to use a normal 6 studs spacer on the front wheels. \u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003ePCD = 139.7 Inner Bore = 100.1mm Thickness = 30mm – Stud = M12x1.5\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003eHave a look at \u003ca href=\"http:\/\/www.wheel-size.com\/size\/\" target=\"_blank\"\u003ehttp:\/\/www.wheel-size.com\/size\/\u003c\/a\u003e to see what size spacer your vehicle use.\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003e\u003cstrong\u003eNOTE: \u003c\/strong\u003ePrice is per spacer!\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003eYou can use these wheel spacers\u003cstrong\u003e \u003c\/strong\u003eto push out the wheel a bit. Some people do it for the looks and others use wheel spacers because they fit new rims and the new rims catches the calipers. Especially on the Hiluxes, if you fit the rims of a newer model on an older Hilux the rims will catch the caliper and you  have to install a set of wheel spacers.\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003eThe wheels spacer bolts onto the vehicle on the existing studs with the nuts supplied. Your wheel then bolts onto the wheel spacer using the studs on the wheel spacer and your original nuts.\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cul\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003eWheel spacer material ALUMINUM\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003eStud – 12×1.5mm – high tensile 10.9 grade\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003eNuts – 40CrMo high tensile steel\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003e30mm thick\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003e139.7 PCD\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cbr\u003e\n\u003cli\u003e\u003cspan\u003e\u003cspan\u003eCentre bore 100.1 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003e\u003cstrong\u003eNotes:\u003c\/strong\u003e Please read full fitment instructions here:\u003c\/span\u003e\u003cbr\u003e\u003ca href=\"http:\/\/www.4x4direct.co.za\/blog\/fitment-instructions-for-wheel-spacers\/\" target=\"_blank\"\u003ehttp:\/\/www.4x4direct.co.za\/blog\/fitment-instructions-for-wheel-spacers\/\u003c\/a\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003eMake sure the surface on the vehicle hub is clean and free from any debris before fitment.\u003cbr\u003eThe same applies to the back of the wheel spacer which should be clean.\u003cbr\u003eTighten all nuts by hand first, then torque in cross over sequence to 30 Nm. Then Torque to 120Nm.\u003cbr\u003eWhen you have them fitted at a tyre fitment centre, keep an eye on the procedures because they normally tighten it with impact wrench. DO NOT allow them to use an impact wrench and make sure they tighten them in cross over sequence.\u003cbr\u003eCheck the wheel spacer nuts after the first 500 km to make sure they are tight. Thereafter check every 5000km.\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e\u003cspan\u003e\u003cspan\u003e\u003cspan\u003e\u003cspan\u003e\u003cfont size=\"2\"\u003e\u003cstrong\u003e* The use of thread locker will void the warranty of these wheel spacers\u003cbr\u003eReason: How do you frequently check the torque if you used thread locker?\u003c\/strong\u003e\u003c\/font\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e \u003c\/p\u003e\u003cbr\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"BakkieBoss","offers":[{"title":"Default Title","offer_id":56913590616224,"sku":"WSPACER-ISUZU-SPI","price":600.0,"currency_code":"ZAR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/3857\/3472\/files\/siproduct-7437-8446-67a56658683ea0971a7de6d76c906452c0e1c606.jpg?v=1775835291","url":"https:\/\/bakkieboss.com\/products\/isuzu-and-gwm-p-series-wheel-spacer-with-spigot","provider":"Bakkieboss.com","version":"1.0","type":"link"}